1 PHASE – MDS START AND PERMANENT CAPACITOR

A-Mechanical Properties

The motors are produced in single-phase, totally enclosed, short-circuit rotor, and fan-cooled designs among the IEC 63 – 90 frame sizes.

Construction Type All frame sizes can be manufactured in foot-mounted, flange-mounted, and foot-flange configurations.

Protection Class

a) The standard protection class is IP 54.

b) Fixed ball bearings with ZZ covers are used for the bearings.

c) The shaft ends are threaded according to DIN 332-2. A keyway is opened in accordance with DIN 6885-1. Motors are delivered with a key installed.

d) The cooling fans are made of heat-resistant material and can operate in both directions.

e) The paint is gray and resistant to corrosion. Different color applications can be made upon request.

B-Construction Features

Stator Housing and Covers The housing and covers are made of aluminum alloy with heat conduction properties. The fan cover is made of sheet metal.

Terminal Box It is located on the top of the housing and close to the shaft side. There is a permanent capacitor slot.

Capacitors The motors are produced with permanent circuit capacitors.

C-Electrical Properties

Voltage and Frequency
The motors are normally designed for 230V, 50 Hz. Motors can also be produced for different voltages and frequencies upon request.

Technical Information
The values provided in the table are valid under normal conditions for 230V voltage. The frequency of 50 Hz is valid for an ambient temperature of -20°C to +40°C. The operating time is S1. The sea level is 1000 m. The insulation class of the motors is F, which is resistant up to 155°C.

Special Manufacturing
Custom shafts, special flanges, and motors with different voltages and frequencies, as well as motors with higher protection classes, fixed bearings, and self-cooling features, are produced upon request.

Our motors are manufactured in accordance with IEC recommendations, DIN, and Turkish Standards TS 4239.

TECHNICAL INFORMATION

1 Phase, 230 V, 50 Hz
Insulation Class: F
Operating Type: S1 (continuous operation)
Protection Class: IP 55
TYPE LOAD VALUES STARTING VALUES Starting Moment Ratio  Mk/ Mn   Starting Capacitor Permanent Circuit Capacitor Approximate Weight B3
Power Speed Current Torque Power Factorı Efficiency η Current Ratio Torque Ratio 250 V            µF 450 V            µF
kw hp V d/d A Nm cos φ % IA/IN MA/ MN kg
2 pole-3000 d/d
63 2A 0.18 0.25 230 2820 1.5 0.62 0.91 62 4.8 2.8 2.3 43 – 53 8 4.4
63 2B 0.25 0.34 230 2860 1.55 0.84 0.96 71 5 2.4 2.1 43 – 53 10 4.8
71 2A 0.37 0.50 230 2860 2.5 1.25 0.98 69 5 1.6 2 64 – 77 15 6.5
71 2B 0.55 0.75 230 2835 3.9 1.86 0.98 70 5.3 3.1 2.5 124 – 149 20 7.9
80 2a 0.37 0.50 230 2830 3.2 1.25 0.85 62 4.2 2.5 2.4 64 – 77 15 7.3
  80 2b 0.55 0.75 230 2840 3.9 1.86 0.98 70 5.3 3.1 2.5 124 – 149 20 8.1
80 2A 0.75 1.0 230 2865 5.1 2.58 0.91 71 5.1 2.6 2.2 124 – 149 25 9.2
80 2B 1.1 1.5 230 2820 7.5 3.75 0.92 72 4.3 2.3 2.1 124 – 149 25 10.5
90 2a 0.75 1.0 230 2865 5.1 2.58 0.91 71 5.1 2.5 2.2 124 – 149 25 9.6
90 2A 1.1 1.5 230 2890 7.4 3.75 0.91 71 5.9 3.2 3 145 – 175 30 11.6
90 2B 1.5 2.0 230 2880 9.9 5 0.91 75 5.9 3.5 2.6 280 – 333 40 13.5
90 2C 2.2 3.0 230 2830 13.6 7.55 0.93 79 4.8 3 2.2 280 – 333 50 16.4
4 pole-1500 d/d
63 4A 0.12 0.16 230 1430 0.9 0.80 0.92 66 5.7 2.3 1.9 43 – 53 8 4.4
63 4B 0.18 0.25 230 1420 1.5 1.22 0.95 58 4.6 2.6 2.1 43 – 53 15 5.2
71 4a 0.18 0.25 230 1410 1.5 1.23 0.84 62 4.6 2.5 1,6 43 – 53 10 5.3
71 4A 0.25 0.34 230 1410 2 1.7 0.84 67 4.2 2.3 2.1 43 – 53 10 6.2
71 4B 0.37 0.50 230 1390 2.95 2.55 0.92 62 4.1 2.2 1.9 64 – 77 15 7.1
80 4a 0.37 0.50 230 1420 2.95 2.52 0.82 62 4.1 2.2 1.9 64 – 77 15 7.8
80 4A 0.55 0.75 230 1420 3.8 3.75 0.88 74 4.8 2.3 1.8 124 – 149 20 9.3
80 4B 0.75 1.0 230 1420 5.5 5 0.88 70 4.3 1.8 1.9 124 – 149 25 10.7
90 4a 0.55 0.75 230 1420 3.8 3.75 0.84 74 4.8 2.3 1.8 124 – 149 20 9.3
90 4b 0.75 1.0 230 1420 5.5 5 0.84 76 5.2 2.7 2 145 – 175 25 11.2
90S 4B 1.1 1.5 230 1400 7.2 7.5 0.93 75 5.5 2.6 1.9 189 – 227 30 13.4
90L 4C 1.5 2.0 230 1400 9.5 10 0.93 77 5 2.4 1.9 189 – 227 40 14.6
Structure Size Number of Poles MAIN DIMENSIONS FOOTED MOTORS SHAFT END FLANGED MOTORS
ACø L H HD HA A AB K1 B BB Kø C Dø(1) E DB GA FxG(2) Structure Shape Pø Nø(3) Mø Sø T AD ~
63 2-4 122 205 63 180 7 100 120 10 80 102 7 40 11 23 M4 12.5 4×4 B5 140 95 115 10 3 141
B14 90 60 75 M5 3
71 2-4 139 243 71 180 8 112 135 11 90 109 7 45 14 30 M5 16 5×5 B5 160 110 130 10 3 149
B14 105 70 85 M6 3
80 2-4 155 278 80 210 9 125 152 13 100 129 9 50 19 40 M6 21.5 6×6 B5 200 130 165 12 3 153
B14 120 80 100 M6 3
90 2-4 171 312 90 248 12 140 180 15 100 130 10 56 24 50 M8 31 8×7 B5 200 130 165 12 3.5 158
B14 142 110 130 M8 3.5
( 1 ) Tolerance ISO ” k6 “ All dimensions are in mm.
( 2 ) According to DIN 6885
( 3 ) Tolerance ISO ” j6 “